{"title":"Salvage Row","description":"\u003cp\u003eGenuine period fittings, rescued and rewired. Edwardian gas conversions, Art Deco chrome, Regency ormolu and Gothic Revival iron. When one sells it is gone.\u003c\/p\u003e","products":[{"product_id":"salvage-row-restored-edwardian-brass-gas-converted-wall-light-single","title":"Salvage Row Restored Edwardian Brass Gas Converted Wall Light Single","description":"\u003cp\u003eOriginally a gas bracket, converted to electricity at some point before the war and converted again by us to something a modern electrician will sign off. The gas tap is still there and still turns, because removing it would be vandalism.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, brass, some pitting consistent with age\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1905\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.2 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 5.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767045132620,"sku":"SCH-ANT-001-RW","price":1249.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767045165388,"sku":"SCH-ANT-001-PL","price":1299.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Edwardian_Brass_Gas_Converted_Wall_Light_Single.jpg?v=1789048930"},{"product_id":"salvage-row-restored-edwardian-brass-gas-converted-wall-light-pair","title":"Salvage Row Restored Edwardian Brass Gas Converted Wall Light Pair","description":"\u003cp\u003eOriginally a gas bracket, converted to electricity at some point before the war and converted again by us to something a modern electrician will sign off. The gas tap is still there and still turns, because removing it would be vandalism.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, brass, some pitting consistent with age\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1905\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 10.4 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 10.4 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767045394764,"sku":"SCH-ANT-002-RW","price":2624.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767045427532,"sku":"SCH-ANT-002-PL","price":2724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Edwardian_Brass_Gas_Converted_Wall_Light_Pair.jpg?v=1789048929"},{"product_id":"salvage-row-restored-nineteen-thirties-opaline-glass-wall-light-single","title":"Salvage Row Restored Nineteen Thirties Opaline Glass Wall Light Single","description":"\u003cp\u003eChrome and opaline glass from the years when English factories were still copying Paris. The glass is original and has the slight lens distortion you only get from hand finished opaline.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, chrome over brass, replate available\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1934\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.8 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767045820748,"sku":"SCH-ANT-003-RW","price":979.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767045853516,"sku":"SCH-ANT-003-PL","price":1024.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Nineteen_Thirties_Opaline_Glass_Wall_Light_Single.jpg?v=1789048909"},{"product_id":"salvage-row-restored-nineteen-thirties-opaline-glass-wall-light-pair","title":"Salvage Row Restored Nineteen Thirties Opaline Glass Wall Light Pair","description":"\u003cp\u003eChrome and opaline glass from the years when English factories were still copying Paris. The glass is original and has the slight lens distortion you only get from hand finished opaline.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, chrome over brass, replate available\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1934\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.6 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 7.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767046312268,"sku":"SCH-ANT-004-RW","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767046345036,"sku":"SCH-ANT-004-PL","price":2149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Nineteen_Thirties_Opaline_Glass_Wall_Light_Pair.jpg?v=1789048768"},{"product_id":"salvage-row-restored-french-bronze-rococo-wall-light-single","title":"Salvage Row Restored French Bronze Rococo Wall Light Single","description":"\u003cp\u003eBought out of a house sale near Lyon, cast bronze with the original mercury gilding worn through on the high points. We have left the wear alone. It is the most valuable thing about it.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, bronze with original worn gilding\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1890\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.4 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 7.4 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767046738252,"sku":"SCH-ANT-005-RW","price":1799.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767046771020,"sku":"SCH-ANT-005-PL","price":1874.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_French_Bronze_Rococo_Wall_Light_Single.jpg?v=1789048859"},{"product_id":"salvage-row-restored-french-bronze-rococo-wall-light-pair","title":"Salvage Row Restored French Bronze Rococo Wall Light Pair","description":"\u003cp\u003eBought out of a house sale near Lyon, cast bronze with the original mercury gilding worn through on the high points. We have left the wear alone. It is the most valuable thing about it.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, bronze with original worn gilding\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1890\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 14.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767048147276,"sku":"SCH-ANT-006-RW","price":3774.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767048180044,"sku":"SCH-ANT-006-PL","price":3924.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_French_Bronze_Rococo_Wall_Light_Pair.jpg?v=1789048886"},{"product_id":"salvage-row-restored-arts-and-crafts-hammered-copper-wall-light-single","title":"Salvage Row Restored Arts and Crafts Hammered Copper Wall Light Single","description":"\u003cp\u003eHammered copper with the rivets showing, in the Birmingham Guild manner. The patina is a hundred years deep and nothing we could do would improve it.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, copper, deep original patina\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1912\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.6 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767048769868,"sku":"SCH-ANT-007-RW","price":1399.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767048802636,"sku":"SCH-ANT-007-PL","price":1449.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Arts_and_Crafts_Hammered_Copper_Wall_Light_Single.jpg?v=1789048869"},{"product_id":"salvage-row-restored-arts-and-crafts-hammered-copper-wall-light-pair","title":"Salvage Row Restored Arts and Crafts Hammered Copper Wall Light Pair","description":"\u003cp\u003eHammered copper with the rivets showing, in the Birmingham Guild manner. The patina is a hundred years deep and nothing we could do would improve it.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, copper, deep original patina\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1912\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 9.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767049916748,"sku":"SCH-ANT-008-RW","price":2924.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767049949516,"sku":"SCH-ANT-008-PL","price":3049.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Arts_and_Crafts_Hammered_Copper_Wall_Light_Pair.jpg?v=1789048909"},{"product_id":"salvage-row-restored-victorian-cast-iron-wall-bracket-single","title":"Salvage Row Restored Victorian Cast Iron Wall Bracket Single","description":"\u003cp\u003eA heavy iron bracket off a railway building, stripped back to bare metal, phosphated and waxed. Not delicate and not trying to be.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, cast iron, waxed\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1878\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.8 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 9.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767051194700,"sku":"SCH-ANT-009-RW","price":899.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767051227468,"sku":"SCH-ANT-009-PL","price":929.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Victorian_Cast_Iron_Wall_Bracket_Single.jpg?v=1789048923"},{"product_id":"salvage-row-restored-victorian-cast-iron-wall-bracket-pair","title":"Salvage Row Restored Victorian Cast Iron Wall Bracket Pair","description":"\u003cp\u003eA heavy iron bracket off a railway building, stripped back to bare metal, phosphated and waxed. Not delicate and not trying to be.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, cast iron, waxed\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1878\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 19.6 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 19.6 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767051784524,"sku":"SCH-ANT-010-RW","price":1874.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767051817292,"sku":"SCH-ANT-010-PL","price":1949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Victorian_Cast_Iron_Wall_Bracket_Pair.jpg?v=1789048924"},{"product_id":"salvage-row-restored-art-deco-chrome-and-stepped-glass-wall-light-single","title":"Salvage Row Restored Art Deco Chrome and Stepped Glass Wall Light Single","description":"\u003cp\u003eStepped glass in a chrome frame, the skyscraper shape everyone borrowed from New York for about a decade. The glass has been polished on the edges where it was chipped.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, chrome over brass, glass polished\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1930\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.4 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.4 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767052767564,"sku":"SCH-ANT-011-RW","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767052800332,"sku":"SCH-ANT-011-PL","price":1199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Art_Deco_Chrome_and_Stepped_Glass_Wall_Light_Single.jpg?v=1789048827"},{"product_id":"salvage-row-restored-art-deco-chrome-and-stepped-glass-wall-light-pair","title":"Salvage Row Restored Art Deco Chrome and Stepped Glass Wall Light Pair","description":"\u003cp\u003eStepped glass in a chrome frame, the skyscraper shape everyone borrowed from New York for about a decade. The glass has been polished on the edges where it was chipped.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, chrome over brass, glass polished\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1930\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 8.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 8.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767053160780,"sku":"SCH-ANT-012-RW","price":2399.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767053193548,"sku":"SCH-ANT-012-PL","price":2499.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Art_Deco_Chrome_and_Stepped_Glass_Wall_Light_Pair.jpg?v=1789048917"},{"product_id":"salvage-row-restored-regency-bronze-and-ormolu-wall-light-single","title":"Salvage Row Restored Regency Bronze and Ormolu Wall Light Single","description":"\u003cp\u003ePatinated bronze with ormolu mounts, the fire gilding still bright in the recesses where nobody has polished it. Originally a candle sconce and converted long enough ago that the conversion is itself an antique.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, bronze with original fire gilded mounts\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1820\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.1 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.1 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767053717836,"sku":"SCH-ANT-013-RW","price":1774.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767053750604,"sku":"SCH-ANT-013-PL","price":1849.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Regency_Bronze_and_Ormolu_Wall_Light_Single.jpg?v=1789048897"},{"product_id":"salvage-row-restored-regency-bronze-and-ormolu-wall-light-pair","title":"Salvage Row Restored Regency Bronze and Ormolu Wall Light Pair","description":"\u003cp\u003ePatinated bronze with ormolu mounts, the fire gilding still bright in the recesses where nobody has polished it. Originally a candle sconce and converted long enough ago that the conversion is itself an antique.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, bronze with original fire gilded mounts\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1820\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 12.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767054176588,"sku":"SCH-ANT-014-RW","price":3724.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767054209356,"sku":"SCH-ANT-014-PL","price":3874.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Regency_Bronze_and_Ormolu_Wall_Light_Pair.jpg?v=1789048931"},{"product_id":"salvage-row-restored-nineteen-fifties-italian-brass-and-glass-wall-light-single","title":"Salvage Row Restored Nineteen Fifties Italian Brass and Glass Wall Light Single","description":"\u003cp\u003eBrass and clear glass out of Milan, from the years when Italian lighting was the best in Europe and knew it. Light in the hand and much better made than it looks.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. One fitting only. When it is gone it is gone.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, brass, light surface wear\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1955\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 2.9 kilograms\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 2.9 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767054700876,"sku":"SCH-ANT-015-RW","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767054733644,"sku":"SCH-ANT-015-PL","price":1149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Nineteen_Fifties_Italian_Brass_and_Glass_Wall_Light_Single.jpg?v=1789048878"},{"product_id":"salvage-row-restored-nineteen-fifties-italian-brass-and-glass-wall-light-pair","title":"Salvage Row Restored Nineteen Fifties Italian Brass and Glass Wall Light Pair","description":"\u003cp\u003eBrass and clear glass out of Milan, from the years when Italian lighting was the best in Europe and knew it. Light in the hand and much better made than it looks.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, brass, light surface wear\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1955\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 5.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767055159628,"sku":"SCH-ANT-016-RW","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767055192396,"sku":"SCH-ANT-016-PL","price":2399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Nineteen_Fifties_Italian_Brass_and_Glass_Wall_Light_Pair.jpg?v=1789048902"},{"product_id":"salvage-row-restored-gothic-revival-wrought-iron-wall-bracket-pair","title":"Salvage Row Restored Gothic Revival Wrought Iron Wall Bracket Pair","description":"\u003cp\u003eWrought iron from a church restoration, hand forged rather than cast, with the scarf welds still visible at the joints. Waxed over the original blacksmith finish.\u003c\/p\u003e\u003cp\u003eEverything we sell has been through the same process. Stripped to components, cleaned by hand rather than blasted, rewired end to end with silicone insulated cable, fitted with new lampholders and a proper earth, then PAT tested and certificated. We do not re-plate or re-lacquer unless the original finish has failed, because a hundred years of patina is the reason to buy an antique in the first place. A true original pair, which is rarer and dearer than two singles because they left the factory together.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: see photographs, width see photographs, projection from the wall see photographs\u003c\/li\u003e\n\u003cli\u003eMaterials: original materials, wrought iron, original forge finish under wax\u003c\/li\u003e\n\u003cli\u003eFinish: original finish retained, honest wear present\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: rewired for E14 or E27 depending on the fitting, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: original backplate, may not cover a modern round pattress\u003c\/li\u003e\n\u003cli\u003ePeriod: circa 1865\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 16.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFully rewired with a PAT test certificate\u003c\/li\u003e\n\u003cli\u003eSold as seen, with photographs of every mark before purchase\u003c\/li\u003e\n\u003cli\u003eOne pair only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 16.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone. Original backplates are often smaller than a modern pattress, so check what is behind your existing fitting before you take it off the wall.\u003c\/p\u003e","brand":"Salvage Row","offers":[{"title":"Rewired and PAT tested","offer_id":58767056175436,"sku":"SCH-ANT-018-RW","price":2624.0,"currency_code":"GBP","in_stock":true},{"title":"Rewired with a plug in flex","offer_id":58767056208204,"sku":"SCH-ANT-018-PL","price":2724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Salvage_Row_Restored_Gothic_Revival_Wrought_Iron_Wall_Bracket_Pair.jpg?v=1789048817"}],"url":"https:\/\/thesconcehouse.com\/collections\/salvage-row.oembed","provider":"The Sconce House","version":"1.0","type":"link"}