{"title":"Portland Lantern Works","description":"\u003cp\u003eExterior lanterns in solid brass and copper, including marine grade fittings for coastal exposure. Four patterns, four sizes, singly or in pairs.\u003c\/p\u003e","products":[{"product_id":"portland-lantern-works-portloe-solid-brass-wall-lantern-small","title":"Portland Lantern Works Portloe Solid Brass Wall Lantern Small","description":"\u003cp\u003eA six sided lantern in solid brass, unlacquered so it goes from gold to brown to a soft green over about three years. If you want it to stay gold, order it lacquered and accept that the lacquer will need redoing. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 420mm, width 230mm, projection from the wall 175mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.4 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 3.4 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767056863564,"sku":"SCH-EXT-001-UL","price":539.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767056896332,"sku":"SCH-EXT-001-LQ","price":569.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767056929100,"sku":"SCH-EXT-001-PA","price":589.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Portloe_Solid_Brass_Wall_Lantern_Small_a9916245-bfd9-4c2c-b62f-dae45bad6967.jpg?v=1789048660"},{"product_id":"portland-lantern-works-portloe-solid-brass-wall-lantern-medium","title":"Portland Lantern Works Portloe Solid Brass Wall Lantern Medium","description":"\u003cp\u003eA six sided lantern in solid brass, unlacquered so it goes from gold to brown to a soft green over about three years. If you want it to stay gold, order it lacquered and accept that the lacquer will need redoing. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 520mm, width 285mm, projection from the wall 220mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.8 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 4.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767057420620,"sku":"SCH-EXT-002-UL","price":739.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767057453388,"sku":"SCH-EXT-002-LQ","price":779.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767057486156,"sku":"SCH-EXT-002-PA","price":809.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Portloe_Solid_Brass_Wall_Lantern_Medium_cc8048a1-aa59-4aa4-bb6b-0fe567b3c117.jpg?v=1789048696"},{"product_id":"portland-lantern-works-portloe-solid-brass-wall-lantern-medium-pair","title":"Portland Lantern Works Portloe Solid Brass Wall Lantern Medium Pair","description":"\u003cp\u003eA six sided lantern in solid brass, unlacquered so it goes from gold to brown to a soft green over about three years. If you want it to stay gold, order it lacquered and accept that the lacquer will need redoing. Sold as a pair for either side of a door, made and finished in the same batch so they weather at the same rate.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 520mm, width 285mm, projection from the wall 220mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.6 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. It is a heavy fitting at roughly 9.6 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767059583308,"sku":"SCH-EXT-003-UL","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767059616076,"sku":"SCH-EXT-003-LQ","price":1474.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767059648844,"sku":"SCH-EXT-003-PA","price":1549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Portloe_Solid_Brass_Wall_Lantern_Medium_Pair.jpg?v=1789048697"},{"product_id":"portland-lantern-works-portloe-solid-brass-wall-lantern-large","title":"Portland Lantern Works Portloe Solid Brass Wall Lantern Large","description":"\u003cp\u003eA six sided lantern in solid brass, unlacquered so it goes from gold to brown to a soft green over about three years. If you want it to stay gold, order it lacquered and accept that the lacquer will need redoing. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 620mm, width 340mm, projection from the wall 260mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.9 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 6.9 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767060730188,"sku":"SCH-EXT-004-UL","price":999.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767060762956,"sku":"SCH-EXT-004-LQ","price":1049.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767060795724,"sku":"SCH-EXT-004-PA","price":1074.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Portloe_Solid_Brass_Wall_Lantern_Large_dbe1769d-3ace-4d75-add2-e0224cfce977.jpg?v=1789048656"},{"product_id":"portland-lantern-works-portloe-solid-brass-wall-lantern-large-pair","title":"Portland Lantern Works Portloe Solid Brass Wall Lantern Large Pair","description":"\u003cp\u003eA six sided lantern in solid brass, unlacquered so it goes from gold to brown to a soft green over about three years. If you want it to stay gold, order it lacquered and accept that the lacquer will need redoing. Sold as a pair for either side of a door, made and finished in the same batch so they weather at the same rate.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 620mm, width 340mm, projection from the wall 260mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. It is a heavy fitting at roughly 13.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767061352780,"sku":"SCH-EXT-005-UL","price":1899.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767061385548,"sku":"SCH-EXT-005-LQ","price":1974.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767061418316,"sku":"SCH-EXT-005-PA","price":2049.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Portloe_Solid_Brass_Wall_Lantern_Large_Pair.jpg?v=1789048881"},{"product_id":"portland-lantern-works-rame-copper-wall-lantern-small","title":"Portland Lantern Works Rame Copper Wall Lantern Small","description":"\u003cp\u003eHand seamed copper with a glazed front, made the way a marine lantern is made. Copper goes brown quickly and green slowly, and on a coast it does both faster. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from sheet copper of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 400mm, width 220mm, projection from the wall 170mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid copper with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: copper, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.6 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 3.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767061942604,"sku":"SCH-EXT-006-UL","price":599.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767061975372,"sku":"SCH-EXT-006-LQ","price":619.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767062008140,"sku":"SCH-EXT-006-PA","price":649.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Rame_Copper_Wall_Lantern_Small_7d3ca4a8-2ad6-4efe-8a03-3821ea1d33f1.jpg?v=1789048831"},{"product_id":"portland-lantern-works-rame-copper-wall-lantern-medium","title":"Portland Lantern Works Rame Copper Wall Lantern Medium","description":"\u003cp\u003eHand seamed copper with a glazed front, made the way a marine lantern is made. Copper goes brown quickly and green slowly, and on a coast it does both faster. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from sheet copper of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 500mm, width 275mm, projection from the wall 210mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid copper with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: copper, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.1 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 5.1 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767062565196,"sku":"SCH-EXT-007-UL","price":819.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767062597964,"sku":"SCH-EXT-007-LQ","price":869.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767062630732,"sku":"SCH-EXT-007-PA","price":899.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Rame_Copper_Wall_Lantern_Medium_5b2cd399-f458-4297-8846-45abef0ed961.jpg?v=1789048829"},{"product_id":"portland-lantern-works-rame-copper-wall-lantern-medium-pair","title":"Portland Lantern Works Rame Copper Wall Lantern Medium Pair","description":"\u003cp\u003eHand seamed copper with a glazed front, made the way a marine lantern is made. Copper goes brown quickly and green slowly, and on a coast it does both faster. Sold as a pair for either side of a door, made and finished in the same batch so they weather at the same rate.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from sheet copper of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 500mm, width 275mm, projection from the wall 210mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid copper with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: copper, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 10.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. It is a heavy fitting at roughly 10.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767063089484,"sku":"SCH-EXT-008-UL","price":1574.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767063122252,"sku":"SCH-EXT-008-LQ","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767063155020,"sku":"SCH-EXT-008-PA","price":1699.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Rame_Copper_Wall_Lantern_Medium_Pair.jpg?v=1789048880"},{"product_id":"portland-lantern-works-rame-copper-wall-lantern-large","title":"Portland Lantern Works Rame Copper Wall Lantern Large","description":"\u003cp\u003eHand seamed copper with a glazed front, made the way a marine lantern is made. Copper goes brown quickly and green slowly, and on a coast it does both faster. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from sheet copper of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 600mm, width 330mm, projection from the wall 250mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid copper with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: copper, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.4 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 7.4 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767063646540,"sku":"SCH-EXT-009-UL","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767063679308,"sku":"SCH-EXT-009-LQ","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767063712076,"sku":"SCH-EXT-009-PA","price":1199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Rame_Copper_Wall_Lantern_Large_0f34d52b-2fe1-4ce0-b9b1-7f39f3d41cb1.jpg?v=1789048814"},{"product_id":"portland-lantern-works-rame-copper-wall-lantern-large-pair","title":"Portland Lantern Works Rame Copper Wall Lantern Large Pair","description":"\u003cp\u003eHand seamed copper with a glazed front, made the way a marine lantern is made. Copper goes brown quickly and green slowly, and on a coast it does both faster. Sold as a pair for either side of a door, made and finished in the same batch so they weather at the same rate.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from sheet copper of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 600mm, width 330mm, projection from the wall 250mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid copper with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: copper, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. It is a heavy fitting at roughly 14.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767064301900,"sku":"SCH-EXT-010-UL","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767064334668,"sku":"SCH-EXT-010-LQ","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767064367436,"sku":"SCH-EXT-010-PA","price":2274.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Rame_Copper_Wall_Lantern_Large_Pair.jpg?v=1789048810"},{"product_id":"portland-lantern-works-salcombe-brass-half-lantern-small","title":"Portland Lantern Works Salcombe Brass Half Lantern Small","description":"\u003cp\u003eA half lantern that sits flat to the wall, for a porch or a passage where a full lantern would be in the way. Same construction, half the projection. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 340mm, width 185mm, projection from the wall 145mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 2.4 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 2.4 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767064924492,"sku":"SCH-EXT-011-UL","price":419.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767064957260,"sku":"SCH-EXT-011-LQ","price":449.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767064990028,"sku":"SCH-EXT-011-PA","price":459.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Salcombe_Brass_Half_Lantern_Small_bfbd46e6-51e0-4220-a237-46401aa33196.jpg?v=1789048806"},{"product_id":"portland-lantern-works-salcombe-brass-half-lantern-medium","title":"Portland Lantern Works Salcombe Brass Half Lantern Medium","description":"\u003cp\u003eA half lantern that sits flat to the wall, for a porch or a passage where a full lantern would be in the way. Same construction, half the projection. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 420mm, width 230mm, projection from the wall 175mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.3 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 3.3 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767065317708,"sku":"SCH-EXT-012-UL","price":579.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767065350476,"sku":"SCH-EXT-012-LQ","price":599.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767065383244,"sku":"SCH-EXT-012-PA","price":629.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Salcombe_Brass_Half_Lantern_Medium_8fd3cfeb-a51d-4c79-b735-c80dd84ce81e.jpg?v=1789048867"},{"product_id":"portland-lantern-works-salcombe-brass-half-lantern-medium-pair","title":"Portland Lantern Works Salcombe Brass Half Lantern Medium Pair","description":"\u003cp\u003eA half lantern that sits flat to the wall, for a porch or a passage where a full lantern would be in the way. Same construction, half the projection. Sold as a pair for either side of a door, made and finished in the same batch so they weather at the same rate.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 420mm, width 230mm, projection from the wall 175mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.6 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 6.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767065874764,"sku":"SCH-EXT-013-UL","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767065907532,"sku":"SCH-EXT-013-LQ","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767065940300,"sku":"SCH-EXT-013-PA","price":1199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Salcombe_Brass_Half_Lantern_Medium_Pair.jpg?v=1789048903"},{"product_id":"portland-lantern-works-salcombe-brass-half-lantern-large","title":"Portland Lantern Works Salcombe Brass Half Lantern Large","description":"\u003cp\u003eA half lantern that sits flat to the wall, for a porch or a passage where a full lantern would be in the way. Same construction, half the projection. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 500mm, width 275mm, projection from the wall 210mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.6 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 4.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767066366284,"sku":"SCH-EXT-014-UL","price":799.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767066399052,"sku":"SCH-EXT-014-LQ","price":829.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767066431820,"sku":"SCH-EXT-014-PA","price":869.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Salcombe_Brass_Half_Lantern_Large_ed03c4ce-a726-4c80-adee-ee877c0a47be.jpg?v=1789048841"},{"product_id":"portland-lantern-works-salcombe-brass-half-lantern-large-pair","title":"Portland Lantern Works Salcombe Brass Half Lantern Large Pair","description":"\u003cp\u003eA half lantern that sits flat to the wall, for a porch or a passage where a full lantern would be in the way. Same construction, half the projection. Sold as a pair for either side of a door, made and finished in the same batch so they weather at the same rate.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 500mm, width 275mm, projection from the wall 210mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP54, weather rated for sheltered exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. It is a heavy fitting at roughly 9.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767067054412,"sku":"SCH-EXT-015-UL","price":1499.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767067087180,"sku":"SCH-EXT-015-LQ","price":1574.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767067119948,"sku":"SCH-EXT-015-PA","price":1649.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Salcombe_Brass_Half_Lantern_Large_Pair.jpg?v=1789048921"},{"product_id":"portland-lantern-works-trevose-heavy-marine-grade-brass-wall-light-small","title":"Portland Lantern Works Trevose Heavy Marine Grade Brass Wall Light Small","description":"\u003cp\u003eThe heavy one, cast rather than fabricated, with a 6mm toughened glass lens and a cast brass guard. Specified for exposed sites where a lighter lantern gets torn off the wall in a gale. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 300mm, width 165mm, projection from the wall 105mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass, 6mm toughened lens and a cast guard\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP65, fully weather rated for exposed exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.2 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 5.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767067447628,"sku":"SCH-EXT-016-UL","price":739.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767067480396,"sku":"SCH-EXT-016-LQ","price":779.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767067513164,"sku":"SCH-EXT-016-PA","price":809.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Trevose_Heavy_Marine_Grade_Brass_Wall_Light_Small_242ba65e-af0e-4d37-8a70-11cce7696571.jpg?v=1789048881"},{"product_id":"portland-lantern-works-trevose-heavy-marine-grade-brass-wall-light-medium","title":"Portland Lantern Works Trevose Heavy Marine Grade Brass Wall Light Medium","description":"\u003cp\u003eThe heavy one, cast rather than fabricated, with a 6mm toughened glass lens and a cast brass guard. Specified for exposed sites where a lighter lantern gets torn off the wall in a gale. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 380mm, width 210mm, projection from the wall 135mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass, 6mm toughened lens and a cast guard\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP65, fully weather rated for exposed exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.8 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. At roughly 7.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767068037452,"sku":"SCH-EXT-017-UL","price":1049.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767068070220,"sku":"SCH-EXT-017-LQ","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767068102988,"sku":"SCH-EXT-017-PA","price":1149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Trevose_Heavy_Marine_Grade_Brass_Wall_Light_Medium_2c0eab3d-049d-4975-88c5-21ed0c1c3b7d.jpg?v=1789048879"},{"product_id":"portland-lantern-works-trevose-heavy-marine-grade-brass-wall-light-medium-pair","title":"Portland Lantern Works Trevose Heavy Marine Grade Brass Wall Light Medium Pair","description":"\u003cp\u003eThe heavy one, cast rather than fabricated, with a 6mm toughened glass lens and a cast brass guard. Specified for exposed sites where a lighter lantern gets torn off the wall in a gale. Sold as a pair for either side of a door, made and finished in the same batch so they weather at the same rate.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 380mm, width 210mm, projection from the wall 135mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass, 6mm toughened lens and a cast guard\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP65, fully weather rated for exposed exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 15.6 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. It is a heavy fitting at roughly 15.6 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767068954956,"sku":"SCH-EXT-018-UL","price":1974.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767068987724,"sku":"SCH-EXT-018-LQ","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767069020492,"sku":"SCH-EXT-018-PA","price":2174.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Trevose_Heavy_Marine_Grade_Brass_Wall_Light_Medium_Pair.jpg?v=1789048878"},{"product_id":"portland-lantern-works-trevose-heavy-marine-grade-brass-wall-light-large","title":"Portland Lantern Works Trevose Heavy Marine Grade Brass Wall Light Large","description":"\u003cp\u003eThe heavy one, cast rather than fabricated, with a 6mm toughened glass lens and a cast brass guard. Specified for exposed sites where a lighter lantern gets torn off the wall in a gale. Sold singly.\u003c\/p\u003e\u003cp\u003eMade in Cornwall from solid brass of a gauge that is heavier than it needs to be. Every seam is silver soldered, not glued and not riveted, and the glass is bedded on a silicone gasket that can be replaced without breaking anything. Marine grade stainless fixings are supplied because plated steel screws will streak the wall inside a winter.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 460mm, width 255mm, projection from the wall 160mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass with 4mm clear glass, 6mm toughened lens and a cast guard\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered as standard so it patinates, lacquered to order\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, cable gland fitted in the base\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch, a photocell or a PIR\u003c\/li\u003e\n\u003cli\u003eRating: IP65, fully weather rated for exposed exterior walls\u003c\/li\u003e\n\u003cli\u003eBackplate: brass, gasketed, with marine grade stainless fixings\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 11.2 kilograms\u003c\/li\u003e\n\u003cli\u003eFixings: A4 marine grade stainless, supplied\u003c\/li\u003e\n\u003cli\u003eGlass: replaceable without special tools\u003c\/li\u003e\n\u003cli\u003ePhotocell and PIR versions available to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired exterior fitting and should be installed by a qualified electrician working to BS 7671. The gasket and cable gland are supplied. Bed the backplate onto a bead of neutral cure silicone and leave the lower edge open so any moisture can drain. It is a heavy fitting at roughly 11.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Portland Lantern Works","offers":[{"title":"Unlacquered, will patinate","offer_id":58767069577548,"sku":"SCH-EXT-019-UL","price":1449.0,"currency_code":"GBP","in_stock":true},{"title":"Lacquered","offer_id":58767069610316,"sku":"SCH-EXT-019-LQ","price":1524.0,"currency_code":"GBP","in_stock":true},{"title":"Pre aged","offer_id":58767069643084,"sku":"SCH-EXT-019-PA","price":1574.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Portland_Lantern_Works_Trevose_Heavy_Marine_Grade_Brass_Wall_Light_Large_1ae5943a-d077-40fe-8ddf-a764db1fe950.jpg?v=1789048860"}],"url":"https:\/\/thesconcehouse.com\/collections\/portland-lantern-works.oembed","provider":"The Sconce House","version":"1.0","type":"link"}