{"title":"Bedside Wall Lights","description":"\u003cp\u003eWall lights made for the side of a bed: swing arms you can pull over a book, fittings with a switch on the backplate, and shelf lights that free up the table.\u003c\/p\u003e","products":[{"product_id":"vellum-stone-ashcombe-alabaster-half-moon-uplighter-wall-light","title":"Vellum Stone Ashcombe Alabaster Half Moon Uplighter Wall Light","description":"\u003cp\u003eThe half moon is the quietest way to light a wall. The alabaster is cut from a single block, so the veining runs unbroken across the face and the light picks it out as a slow amber drift rather than a pattern.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 180mm, width 300mm, projection from the wall 110mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.4 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.4 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766937063756,"sku":"SCH-ALB-001-AB","price":1049.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766937096524,"sku":"SCH-ALB-001-PN","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766937129292,"sku":"SCH-ALB-001-BZ","price":1149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Ashcombe_Alabaster_Half_Moon_Uplighter_Wall_Light.jpg?v=1789048779"},{"product_id":"vellum-stone-ashcombe-alabaster-half-moon-uplighter-wall-light-pair","title":"Vellum Stone Ashcombe Alabaster Half Moon Uplighter Wall Light Pair","description":"\u003cp\u003eThe half moon is the quietest way to light a wall. The alabaster is cut from a single block, so the veining runs unbroken across the face and the light picks it out as a slow amber drift rather than a pattern.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 180mm, width 300mm, projection from the wall 110mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x E14 candle, maximum 40W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766937260364,"sku":"SCH-ALB-002-AB","price":1974.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766937293132,"sku":"SCH-ALB-002-PN","price":2099.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766937325900,"sku":"SCH-ALB-002-BZ","price":2174.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Ashcombe_Alabaster_Half_Moon_Uplighter_Wall_Light_Pair.jpg?v=1789048524"},{"product_id":"vellum-stone-bramfield-alabaster-tapered-cylinder-wall-light","title":"Vellum Stone Bramfield Alabaster Tapered Cylinder Wall Light","description":"\u003cp\u003eA tapered cylinder of white alabaster on a slim brass stem. It throws a soft column of light up the wall and a warmer pool down onto whatever sits below it, which is why it works either side of a bed.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 260mm, width 140mm, projection from the wall 150mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x G9, maximum 33W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.1 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.1 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766937456972,"sku":"SCH-ALB-004-AB","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766937489740,"sku":"SCH-ALB-004-PN","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766937522508,"sku":"SCH-ALB-004-BZ","price":1199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Bramfield_Alabaster_Tapered_Cylinder_Wall_Light.jpg?v=1789048531"},{"product_id":"vellum-stone-bramfield-alabaster-tapered-cylinder-wall-light-pair","title":"Vellum Stone Bramfield Alabaster Tapered Cylinder Wall Light Pair","description":"\u003cp\u003eA tapered cylinder of white alabaster on a slim brass stem. It throws a soft column of light up the wall and a warmer pool down onto whatever sits below it, which is why it works either side of a bed.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 260mm, width 140mm, projection from the wall 150mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x G9, maximum 33W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766937555276,"sku":"SCH-ALB-005-AB","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766937588044,"sku":"SCH-ALB-005-PN","price":2199.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766937620812,"sku":"SCH-ALB-005-BZ","price":2274.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Bramfield_Alabaster_Tapered_Cylinder_Wall_Light_Pair.jpg?v=1789048842"},{"product_id":"vellum-stone-bramfield-alabaster-tapered-cylinder-wall-light-large","title":"Vellum Stone Bramfield Alabaster Tapered Cylinder Wall Light Large","description":"\u003cp\u003eA tapered cylinder of white alabaster on a slim brass stem. It throws a soft column of light up the wall and a warmer pool down onto whatever sits below it, which is why it works either side of a bed.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly in the larger size, 30 per cent taller than the standard fitting.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 340mm, width 180mm, projection from the wall 195mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x G9, maximum 33W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.65 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.7 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766937653580,"sku":"SCH-ALB-006-AB","price":1699.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766937686348,"sku":"SCH-ALB-006-PN","price":1799.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766937719116,"sku":"SCH-ALB-006-BZ","price":1849.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Bramfield_Alabaster_Tapered_Cylinder_Wall_Light_Large_552a9bcf-0164-4714-ad5a-00592b0f49c7.jpg?v=1789048782"},{"product_id":"vellum-stone-colwyn-alabaster-backlit-oval-disc-wall-light","title":"Vellum Stone Colwyn Alabaster Backlit Oval Disc Wall Light","description":"\u003cp\u003eA flat oval of cream alabaster set 40mm off the wall on hidden brass standoffs. The lamp sits behind it, so you never see a bulb, only the stone glowing from the inside with a bright halo on the plaster behind.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 320mm, width 220mm, projection from the wall 70mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x G9, maximum 33W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.2 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766937751884,"sku":"SCH-ALB-007-AB","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766937784652,"sku":"SCH-ALB-007-PN","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766937817420,"sku":"SCH-ALB-007-BZ","price":1249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Colwyn_Alabaster_Backlit_Oval_Disc_Wall_Light.jpg?v=1789048675"},{"product_id":"vellum-stone-colwyn-alabaster-backlit-oval-disc-wall-light-pair","title":"Vellum Stone Colwyn Alabaster Backlit Oval Disc Wall Light Pair","description":"\u003cp\u003eA flat oval of cream alabaster set 40mm off the wall on hidden brass standoffs. The lamp sits behind it, so you never see a bulb, only the stone glowing from the inside with a bright halo on the plaster behind.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 320mm, width 220mm, projection from the wall 70mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x G9, maximum 33W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 8.4 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 8.4 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766937850188,"sku":"SCH-ALB-008-AB","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766937882956,"sku":"SCH-ALB-008-PN","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766937915724,"sku":"SCH-ALB-008-BZ","price":2374.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Colwyn_Alabaster_Backlit_Oval_Disc_Wall_Light_Pair.jpg?v=1789048633"},{"product_id":"vellum-stone-dorney-alabaster-carved-scallop-shell-wall-light","title":"Vellum Stone Dorney Alabaster Carved Scallop Shell Wall Light","description":"\u003cp\u003eA scallop shell carved by hand from honey alabaster, a form that has been used on English walls since the eighteenth century. Every shell is slightly different because the flutes are cut by eye rather than by machine.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 300mm, width 260mm, projection from the wall 130mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.8 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938046796,"sku":"SCH-ALB-010-AB","price":1074.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938079564,"sku":"SCH-ALB-010-PN","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938112332,"sku":"SCH-ALB-010-BZ","price":1174.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Dorney_Alabaster_Carved_Scallop_Shell_Wall_Light.jpg?v=1789048638"},{"product_id":"vellum-stone-dorney-alabaster-carved-scallop-shell-wall-light-pair","title":"Vellum Stone Dorney Alabaster Carved Scallop Shell Wall Light Pair","description":"\u003cp\u003eA scallop shell carved by hand from honey alabaster, a form that has been used on English walls since the eighteenth century. Every shell is slightly different because the flutes are cut by eye rather than by machine.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 300mm, width 260mm, projection from the wall 130mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x E14 candle, maximum 40W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.6 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 9.6 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938145100,"sku":"SCH-ALB-011-AB","price":2049.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938177868,"sku":"SCH-ALB-011-PN","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938210636,"sku":"SCH-ALB-011-BZ","price":2224.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Dorney_Alabaster_Carved_Scallop_Shell_Wall_Light_Pair.jpg?v=1789048637"},{"product_id":"vellum-stone-eversholt-alabaster-fluted-column-wall-light","title":"Vellum Stone Eversholt Alabaster Fluted Column Wall Light","description":"\u003cp\u003eA fluted column in the classical manner, cut so the flutes deepen towards the base. Lit from within it reads as a soft vertical stripe, which suits a tall hallway or the flank of a chimney breast.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 420mm, width 150mm, projection from the wall 120mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.6 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 5.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938243404,"sku":"SCH-ALB-012-AB","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938276172,"sku":"SCH-ALB-012-PN","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938308940,"sku":"SCH-ALB-012-BZ","price":1249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Eversholt_Alabaster_Fluted_Column_Wall_Light.jpg?v=1789048639"},{"product_id":"vellum-stone-eversholt-alabaster-fluted-column-wall-light-pair","title":"Vellum Stone Eversholt Alabaster Fluted Column Wall Light Pair","description":"\u003cp\u003eA fluted column in the classical manner, cut so the flutes deepen towards the base. Lit from within it reads as a soft vertical stripe, which suits a tall hallway or the flank of a chimney breast.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 420mm, width 150mm, projection from the wall 120mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x E14 candle, maximum 40W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 11.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 11.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938341708,"sku":"SCH-ALB-013-AB","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938374476,"sku":"SCH-ALB-013-PN","price":2324.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938407244,"sku":"SCH-ALB-013-BZ","price":2374.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Eversholt_Alabaster_Fluted_Column_Wall_Light_Pair.jpg?v=1789048682"},{"product_id":"vellum-stone-eversholt-alabaster-fluted-column-wall-light-large","title":"Vellum Stone Eversholt Alabaster Fluted Column Wall Light Large","description":"\u003cp\u003eA fluted column in the classical manner, cut so the flutes deepen towards the base. Lit from within it reads as a soft vertical stripe, which suits a tall hallway or the flank of a chimney breast.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly in the larger size, 30 per cent taller than the standard fitting.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 545mm, width 195mm, projection from the wall 155mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 8.399999999999999 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 8.4 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938440012,"sku":"SCH-ALB-014-AB","price":1774.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938472780,"sku":"SCH-ALB-014-PN","price":1899.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938505548,"sku":"SCH-ALB-014-BZ","price":1949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Eversholt_Alabaster_Fluted_Column_Wall_Light_Large_b50b8bce-2062-4b09-baf2-1298185608c5.jpg?v=1789048743"},{"product_id":"vellum-stone-fenwick-alabaster-bowl-uplighter-on-a-brass-arm-wall-light","title":"Vellum Stone Fenwick Alabaster Bowl Uplighter on a Brass Arm Wall Light","description":"\u003cp\u003eA shallow alabaster bowl carried on a cast brass arm that curves away from the wall. The bowl throws almost all of its light at the ceiling, so a pair will lift a low room without anything glaring at eye level.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 240mm, width 280mm, projection from the wall 230mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.5 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.5 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938538316,"sku":"SCH-ALB-015-AB","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938571084,"sku":"SCH-ALB-015-PN","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938603852,"sku":"SCH-ALB-015-BZ","price":1299.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Fenwick_Alabaster_Bowl_Uplighter_on_a_Brass_Arm_Wall_Light.jpg?v=1789048701"},{"product_id":"vellum-stone-fenwick-alabaster-bowl-uplighter-on-a-brass-arm-wall-light-pair","title":"Vellum Stone Fenwick Alabaster Bowl Uplighter on a Brass Arm Wall Light Pair","description":"\u003cp\u003eA shallow alabaster bowl carried on a cast brass arm that curves away from the wall. The bowl throws almost all of its light at the ceiling, so a pair will lift a low room without anything glaring at eye level.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 240mm, width 280mm, projection from the wall 230mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.0 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 9.0 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938636620,"sku":"SCH-ALB-016-AB","price":2274.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938669388,"sku":"SCH-ALB-016-PN","price":2399.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938702156,"sku":"SCH-ALB-016-BZ","price":2474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Fenwick_Alabaster_Bowl_Uplighter_on_a_Brass_Arm_Wall_Light_Pair.jpg?v=1789048701"},{"product_id":"vellum-stone-grantley-alabaster-edge-lit-rectangular-slab-wall-light","title":"Vellum Stone Grantley Alabaster Edge Lit Rectangular Slab Wall Light","description":"\u003cp\u003eA rectangular slab of pale alabaster lit along its top and bottom edges by two concealed strips. The stone lights evenly from the inside with no hot spot, which is difficult to achieve and the reason this one takes longest to make.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 400mm, width 180mm, projection from the wall 80mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 2 x G9, maximum 33W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.2 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938767692,"sku":"SCH-ALB-017-AB","price":1349.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938800460,"sku":"SCH-ALB-017-PN","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938833228,"sku":"SCH-ALB-017-BZ","price":1474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Grantley_Alabaster_Edge_Lit_Rectangular_Slab_Wall_Light.jpg?v=1789048586"},{"product_id":"vellum-stone-grantley-alabaster-edge-lit-rectangular-slab-wall-light-pair","title":"Vellum Stone Grantley Alabaster Edge Lit Rectangular Slab Wall Light Pair","description":"\u003cp\u003eA rectangular slab of pale alabaster lit along its top and bottom edges by two concealed strips. The stone lights evenly from the inside with no hot spot, which is difficult to achieve and the reason this one takes longest to make.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 400mm, width 180mm, projection from the wall 80mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x G9, maximum 33W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.4 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 12.4 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766938865996,"sku":"SCH-ALB-018-AB","price":2549.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766938898764,"sku":"SCH-ALB-018-PN","price":2699.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766938931532,"sku":"SCH-ALB-018-BZ","price":2774.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Grantley_Alabaster_Edge_Lit_Rectangular_Slab_Wall_Light_Pair.jpg?v=1789048682"},{"product_id":"vellum-stone-hindon-alabaster-twin-arm-with-two-shades-wall-light","title":"Vellum Stone Hindon Alabaster Twin Arm with Two Shades Wall Light","description":"\u003cp\u003eTwo alabaster shades on a single cast brass backplate, arms sweeping out in opposite directions. It covers a wide span from one wiring point, which makes it the sensible answer above a wide headboard or a mantelpiece.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 300mm, width 540mm, projection from the wall 160mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 2 x E14 candle, maximum 40W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.1 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 7.1 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766939455820,"sku":"SCH-ALB-019-AB","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766939488588,"sku":"SCH-ALB-019-PN","price":1499.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766939521356,"sku":"SCH-ALB-019-BZ","price":1549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Hindon_Alabaster_Twin_Arm_with_Two_Shades_Wall_Light.jpg?v=1789048701"},{"product_id":"vellum-stone-hindon-alabaster-twin-arm-with-two-shades-wall-light-pair","title":"Vellum Stone Hindon Alabaster Twin Arm with Two Shades Wall Light Pair","description":"\u003cp\u003eTwo alabaster shades on a single cast brass backplate, arms sweeping out in opposite directions. It covers a wide span from one wiring point, which makes it the sensible answer above a wide headboard or a mantelpiece.\u003c\/p\u003e\u003cp\u003eAlabaster is a gypsum stone, soft enough to carve and just translucent enough to hold light without turning it milky. Each piece is cut, turned and hand finished in our Wiltshire workshop, then waxed rather than lacquered so the surface keeps a little of its natural chalk. Expect variation between blocks. That is the point of the material and not a fault. Sold as a matched pair, cut from the same block so the veining reads as a set.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 300mm, width 540mm, projection from the wall 160mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand carved alabaster with a cast brass frame and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: alabaster waxed and unlacquered, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x E14 candle, maximum 40W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round cast brass, 120mm diameter, covers most old fixing holes\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 4 weeks, each piece carved to order\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 14.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vellum Stone","offers":[{"title":"Antique brass","offer_id":58766939554124,"sku":"SCH-ALB-020-AB","price":2699.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766939586892,"sku":"SCH-ALB-020-PN","price":2874.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766939619660,"sku":"SCH-ALB-020-BZ","price":2949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vellum_Stone_Hindon_Alabaster_Twin_Arm_with_Two_Shades_Wall_Light_Pair.jpg?v=1789048587"},{"product_id":"vetro-bianco-palladio-hand-blown-glass-opal-globe-on-brass-wall-light","title":"Vetro Bianco Palladio Hand Blown Glass Opal Globe on Brass Wall Light","description":"\u003cp\u003eA hand blown opal globe held in a brass ring. Opal glass is blown in two layers, a white gather inside a clear one, and that is what stops the lamp showing as a bright point through the wall of the globe.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 230mm, width 230mm, projection from the wall 250mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.2 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.2 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766967865676,"sku":"SCH-GLS-001-AB","price":1049.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766967898444,"sku":"SCH-GLS-001-PB","price":1049.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766967931212,"sku":"SCH-GLS-001-PN","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766967963980,"sku":"SCH-GLS-001-BZ","price":1149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Palladio_Hand_Blown_Glass_Opal_Globe_on_Brass_Wall_Light.jpg?v=1789048685"},{"product_id":"vetro-bianco-palladio-hand-blown-glass-opal-globe-on-brass-wall-light-pair","title":"Vetro Bianco Palladio Hand Blown Glass Opal Globe on Brass Wall Light Pair","description":"\u003cp\u003eA hand blown opal globe held in a brass ring. Opal glass is blown in two layers, a white gather inside a clear one, and that is what stops the lamp showing as a bright point through the wall of the globe.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold as a pair, blown in the same session by the same maker.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 230mm, width 230mm, projection from the wall 250mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.4 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.4 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766969700684,"sku":"SCH-GLS-002-AB","price":1974.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766969733452,"sku":"SCH-GLS-002-PB","price":1974.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766969766220,"sku":"SCH-GLS-002-PN","price":2099.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766969798988,"sku":"SCH-GLS-002-BZ","price":2174.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Palladio_Hand_Blown_Glass_Opal_Globe_on_Brass_Wall_Light_Pair.jpg?v=1789048639"},{"product_id":"vetro-bianco-palladio-hand-blown-glass-opal-globe-on-brass-wall-light-large","title":"Vetro Bianco Palladio Hand Blown Glass Opal Globe on Brass Wall Light Large","description":"\u003cp\u003eA hand blown opal globe held in a brass ring. Opal glass is blown in two layers, a white gather inside a clear one, and that is what stops the lamp showing as a bright point through the wall of the globe.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly in the larger size, roughly a third bigger in every direction.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 305mm, width 305mm, projection from the wall 330mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.5 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.5 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766970716492,"sku":"SCH-GLS-003-AB","price":1474.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766970749260,"sku":"SCH-GLS-003-PB","price":1474.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766970782028,"sku":"SCH-GLS-003-PN","price":1574.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766970814796,"sku":"SCH-GLS-003-BZ","price":1624.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Palladio_Hand_Blown_Glass_Opal_Globe_on_Brass_Wall_Light_Large_87819381-75df-4eeb-bff3-006fa1217c89.jpg?v=1789048490"},{"product_id":"vetro-bianco-querini-hand-blown-glass-fluted-rigadin-cylinder-wall-light","title":"Vetro Bianco Querini Hand Blown Glass Fluted Rigadin Cylinder Wall Light","description":"\u003cp\u003eA cylinder blown into a rigadin mould, which puts a fine vertical rib the whole way round. The ribs break the light into narrow lines, so the fitting reads as a soft sparkle rather than a single bright shape.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 280mm, width 150mm, projection from the wall 170mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.0 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.0 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766972059980,"sku":"SCH-GLS-004-AB","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766972092748,"sku":"SCH-GLS-004-PB","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766972125516,"sku":"SCH-GLS-004-PN","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766972158284,"sku":"SCH-GLS-004-BZ","price":1199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Querini_Hand_Blown_Glass_Fluted_Rigadin_Cylinder_Wall_Light.jpg?v=1789048747"},{"product_id":"vetro-bianco-querini-hand-blown-glass-fluted-rigadin-cylinder-wall-light-pair","title":"Vetro Bianco Querini Hand Blown Glass Fluted Rigadin Cylinder Wall Light Pair","description":"\u003cp\u003eA cylinder blown into a rigadin mould, which puts a fine vertical rib the whole way round. The ribs break the light into narrow lines, so the fitting reads as a soft sparkle rather than a single bright shape.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold as a pair, blown in the same session by the same maker.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 280mm, width 150mm, projection from the wall 170mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.0 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.0 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766974091596,"sku":"SCH-GLS-005-AB","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766974124364,"sku":"SCH-GLS-005-PB","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766974157132,"sku":"SCH-GLS-005-PN","price":2199.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766974189900,"sku":"SCH-GLS-005-BZ","price":2274.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Querini_Hand_Blown_Glass_Fluted_Rigadin_Cylinder_Wall_Light_Pair.jpg?v=1789048686"},{"product_id":"vetro-bianco-querini-hand-blown-glass-fluted-rigadin-cylinder-wall-light-large","title":"Vetro Bianco Querini Hand Blown Glass Fluted Rigadin Cylinder Wall Light Large","description":"\u003cp\u003eA cylinder blown into a rigadin mould, which puts a fine vertical rib the whole way round. The ribs break the light into narrow lines, so the fitting reads as a soft sparkle rather than a single bright shape.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly in the larger size, roughly a third bigger in every direction.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 370mm, width 200mm, projection from the wall 225mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.2 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766975664460,"sku":"SCH-GLS-006-AB","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766975697228,"sku":"SCH-GLS-006-PB","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766975729996,"sku":"SCH-GLS-006-PN","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766975762764,"sku":"SCH-GLS-006-BZ","price":1699.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Querini_Hand_Blown_Glass_Fluted_Rigadin_Cylinder_Wall_Light_Large_31d2f5f4-331d-486f-9003-09b8d6171f5e.jpg?v=1789048746"},{"product_id":"vetro-bianco-rialto-hand-blown-glass-bubble-glass-disc-wall-light","title":"Vetro Bianco Rialto Hand Blown Glass Bubble Glass Disc Wall Light","description":"\u003cp\u003eA flat disc of glass with air deliberately trapped in it, the bubbles set in rows by pressing the gather onto a bed of spikes before the second layer goes on. A Murano trick and still the prettiest way to hold light in flat glass.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 300mm, width 300mm, projection from the wall 110mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 2 x G9, maximum 33W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.4 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 5.4 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766977401164,"sku":"SCH-GLS-007-AB","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766977433932,"sku":"SCH-GLS-007-PB","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766977466700,"sku":"SCH-GLS-007-PN","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766977499468,"sku":"SCH-GLS-007-BZ","price":1299.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Rialto_Hand_Blown_Glass_Bubble_Glass_Disc_Wall_Light.jpg?v=1789048890"},{"product_id":"vetro-bianco-rialto-hand-blown-glass-bubble-glass-disc-wall-light-pair","title":"Vetro Bianco Rialto Hand Blown Glass Bubble Glass Disc Wall Light Pair","description":"\u003cp\u003eA flat disc of glass with air deliberately trapped in it, the bubbles set in rows by pressing the gather onto a bed of spikes before the second layer goes on. A Murano trick and still the prettiest way to hold light in flat glass.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold as a pair, blown in the same session by the same maker.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 300mm, width 300mm, projection from the wall 110mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 2 x G9, maximum 33W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 10.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 10.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766978941260,"sku":"SCH-GLS-008-AB","price":2274.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766978974028,"sku":"SCH-GLS-008-PB","price":2274.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766979006796,"sku":"SCH-GLS-008-PN","price":2399.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766979039564,"sku":"SCH-GLS-008-BZ","price":2474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Rialto_Hand_Blown_Glass_Bubble_Glass_Disc_Wall_Light_Pair.jpg?v=1789048931"},{"product_id":"vetro-bianco-rialto-hand-blown-glass-bubble-glass-disc-wall-light-large","title":"Vetro Bianco Rialto Hand Blown Glass Bubble Glass Disc Wall Light Large","description":"\u003cp\u003eA flat disc of glass with air deliberately trapped in it, the bubbles set in rows by pressing the gather onto a bed of spikes before the second layer goes on. A Murano trick and still the prettiest way to hold light in flat glass.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly in the larger size, roughly a third bigger in every direction.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 400mm, width 400mm, projection from the wall 145mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 2 x G9, maximum 33W each, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.6 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 7.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766981169484,"sku":"SCH-GLS-009-AB","price":1699.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766981202252,"sku":"SCH-GLS-009-PB","price":1699.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766981235020,"sku":"SCH-GLS-009-PN","price":1799.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766981267788,"sku":"SCH-GLS-009-BZ","price":1849.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Rialto_Hand_Blown_Glass_Bubble_Glass_Disc_Wall_Light_Large_3639c08e-a0e5-45c3-aa62-f712386a3781.jpg?v=1789048931"},{"product_id":"vetro-bianco-sansovino-hand-blown-glass-twisted-glass-column-wall-light","title":"Vetro Bianco Sansovino Hand Blown Glass Twisted Glass Column Wall Light","description":"\u003cp\u003eA column of clear glass twisted while still hot, so the whole body turns through about a hundred degrees from base to top. The twist carries the light up the fitting and throws a slow spiral onto the wall behind.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 380mm, width 130mm, projection from the wall 150mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.9 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.9 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766982840652,"sku":"SCH-GLS-010-AB","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766982873420,"sku":"SCH-GLS-010-PB","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766982906188,"sku":"SCH-GLS-010-PN","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766982938956,"sku":"SCH-GLS-010-BZ","price":1249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Sansovino_Hand_Blown_Glass_Twisted_Glass_Column_Wall_Light.jpg?v=1789048750"},{"product_id":"vetro-bianco-sansovino-hand-blown-glass-twisted-glass-column-wall-light-pair","title":"Vetro Bianco Sansovino Hand Blown Glass Twisted Glass Column Wall Light Pair","description":"\u003cp\u003eA column of clear glass twisted while still hot, so the whole body turns through about a hundred degrees from base to top. The twist carries the light up the fitting and throws a slow spiral onto the wall behind.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold as a pair, blown in the same session by the same maker.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 380mm, width 130mm, projection from the wall 150mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 7.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766984118604,"sku":"SCH-GLS-011-AB","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766984151372,"sku":"SCH-GLS-011-PB","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766984184140,"sku":"SCH-GLS-011-PN","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766984216908,"sku":"SCH-GLS-011-BZ","price":2374.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Sansovino_Hand_Blown_Glass_Twisted_Glass_Column_Wall_Light_Pair.jpg?v=1789048891"},{"product_id":"vetro-bianco-sansovino-hand-blown-glass-twisted-glass-column-wall-light-large","title":"Vetro Bianco Sansovino Hand Blown Glass Twisted Glass Column Wall Light Large","description":"\u003cp\u003eA column of clear glass twisted while still hot, so the whole body turns through about a hundred degrees from base to top. The twist carries the light up the fitting and throws a slow spiral onto the wall behind.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly in the larger size, roughly a third bigger in every direction.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 505mm, width 175mm, projection from the wall 200mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.5 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 5.5 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766985527628,"sku":"SCH-GLS-012-AB","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766985560396,"sku":"SCH-GLS-012-PB","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766985593164,"sku":"SCH-GLS-012-PN","price":1724.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766985625932,"sku":"SCH-GLS-012-BZ","price":1774.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Sansovino_Hand_Blown_Glass_Twisted_Glass_Column_Wall_Light_Large_9b419df0-c6ad-43f2-aaf0-51d58f3ea322.jpg?v=1789048788"},{"product_id":"vetro-bianco-torcello-hand-blown-glass-smoked-amber-shade-wall-light","title":"Vetro Bianco Torcello Hand Blown Glass Smoked Amber Shade Wall Light","description":"\u003cp\u003eA conical shade in smoked amber, the colour laid in as a thin flash over clear glass so it darkens towards the rim. It takes the edge off a bright lamp and warms a cold north facing room.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 210mm, width 220mm, projection from the wall 240mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.4 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.4 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766986838348,"sku":"SCH-GLS-013-AB","price":1024.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766986871116,"sku":"SCH-GLS-013-PB","price":1024.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766986903884,"sku":"SCH-GLS-013-PN","price":1074.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766986936652,"sku":"SCH-GLS-013-BZ","price":1124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Torcello_Hand_Blown_Glass_Smoked_Amber_Shade_Wall_Light.jpg?v=1789048876"},{"product_id":"vetro-bianco-torcello-hand-blown-glass-smoked-amber-shade-wall-light-pair","title":"Vetro Bianco Torcello Hand Blown Glass Smoked Amber Shade Wall Light Pair","description":"\u003cp\u003eA conical shade in smoked amber, the colour laid in as a thin flash over clear glass so it darkens towards the rim. It takes the edge off a bright lamp and warms a cold north facing room.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold as a pair, blown in the same session by the same maker.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 210mm, width 220mm, projection from the wall 240mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766988673356,"sku":"SCH-GLS-014-AB","price":1949.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766988706124,"sku":"SCH-GLS-014-PB","price":1949.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766988738892,"sku":"SCH-GLS-014-PN","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766988771660,"sku":"SCH-GLS-014-BZ","price":2124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Torcello_Hand_Blown_Glass_Smoked_Amber_Shade_Wall_Light_Pair.jpg?v=1789048688"},{"product_id":"vetro-bianco-torcello-hand-blown-glass-smoked-amber-shade-wall-light-large","title":"Vetro Bianco Torcello Hand Blown Glass Smoked Amber Shade Wall Light Large","description":"\u003cp\u003eA conical shade in smoked amber, the colour laid in as a thin flash over clear glass so it darkens towards the rim. It takes the edge off a bright lamp and warms a cold north facing room.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly in the larger size, roughly a third bigger in every direction.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 280mm, width 295mm, projection from the wall 320mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.8 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766990278988,"sku":"SCH-GLS-015-AB","price":1449.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766990311756,"sku":"SCH-GLS-015-PB","price":1449.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766990344524,"sku":"SCH-GLS-015-PN","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766990377292,"sku":"SCH-GLS-015-BZ","price":1574.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Torcello_Hand_Blown_Glass_Smoked_Amber_Shade_Wall_Light_Large_06473ebf-1b2d-44fa-810f-471a1779ed58.jpg?v=1789048687"},{"product_id":"vetro-bianco-vendramin-hand-blown-glass-clear-glass-lantern-on-a-brass-arm-wall-light","title":"Vetro Bianco Vendramin Hand Blown Glass Clear Glass Lantern on a Brass Arm Wall Light","description":"\u003cp\u003eA six sided lantern in clear glass carried on a brass arm that stands well off the wall. Because the glass is clear you see the lamp, so fit a decorative filament LED and let it be the ornament.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 400mm, width 200mm, projection from the wall 290mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.1 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.1 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766991982924,"sku":"SCH-GLS-016-AB","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766992015692,"sku":"SCH-GLS-016-PB","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766992048460,"sku":"SCH-GLS-016-PN","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766992081228,"sku":"SCH-GLS-016-BZ","price":1249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Vendramin_Hand_Blown_Glass_Clear_Glass_Lantern_on_a_Brass_Arm_Wall_Light.jpg?v=1789048705"},{"product_id":"vetro-bianco-vendramin-hand-blown-glass-clear-glass-lantern-on-a-brass-arm-wall-light-pair","title":"Vetro Bianco Vendramin Hand Blown Glass Clear Glass Lantern on a Brass Arm Wall Light Pair","description":"\u003cp\u003eA six sided lantern in clear glass carried on a brass arm that stands well off the wall. Because the glass is clear you see the lamp, so fit a decorative filament LED and let it be the ornament.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold as a pair, blown in the same session by the same maker.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 400mm, width 200mm, projection from the wall 290mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 12.2 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766994178380,"sku":"SCH-GLS-017-AB","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766994211148,"sku":"SCH-GLS-017-PB","price":2174.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766994243916,"sku":"SCH-GLS-017-PN","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766994276684,"sku":"SCH-GLS-017-BZ","price":2374.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Vendramin_Hand_Blown_Glass_Clear_Glass_Lantern_on_a_Brass_Arm_Wall_Light_Pair.jpg?v=1789048596"},{"product_id":"vetro-bianco-vendramin-hand-blown-glass-clear-glass-lantern-on-a-brass-arm-wall-light-large","title":"Vetro Bianco Vendramin Hand Blown Glass Clear Glass Lantern on a Brass Arm Wall Light Large","description":"\u003cp\u003eA six sided lantern in clear glass carried on a brass arm that stands well off the wall. Because the glass is clear you see the lamp, so fit a decorative filament LED and let it be the ornament.\u003c\/p\u003e\u003cp\u003eBlown by mouth on the Venetian lagoon by a workshop we have bought from for years. Nothing is pressed and nothing is moulded except where the pattern needs a mould, so no two pieces are identical in wall thickness or in the exact set of the shoulder. Brass parts are made in England and the two are married here. Sold singly in the larger size, roughly a third bigger in every direction.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 530mm, width 265mm, projection from the wall 385mm\u003c\/li\u003e\n\u003cli\u003eMaterials: hand blown glass with solid brass fittings and backplate\u003c\/li\u003e\n\u003cli\u003eFinish: glass as described, brass in your chosen finish\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: no integral switch, wired to a wall switch or a dimmer circuit\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 100mm diameter\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 8.5 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 3 to 5 weeks from Murano\u003c\/li\u003e\n\u003cli\u003eSmall bubbles and slight variation in the glass are evidence of hand blowing and are not faults\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 8.5 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Vetro Bianco","offers":[{"title":"Antique brass","offer_id":58766995652940,"sku":"SCH-GLS-018-AB","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58766995685708,"sku":"SCH-GLS-018-PB","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58766995718476,"sku":"SCH-GLS-018-PN","price":1724.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58766995751244,"sku":"SCH-GLS-018-BZ","price":1774.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Vetro_Bianco_Vendramin_Hand_Blown_Glass_Clear_Glass_Lantern_on_a_Brass_Arm_Wall_Light_Large_85c0b6c3-b43a-416c-9074-294243666b3b.jpg?v=1789048706"},{"product_id":"marlow-and-reade-hollis-solid-brass-swing-arm-with-a-linen-shade-wall-light","title":"Marlow and Reade Hollis Solid Brass Swing Arm with a Linen Shade Wall Light","description":"\u003cp\u003eA single jointed swing arm with a hand rolled linen shade. The joint is a brass friction knuckle you tighten with a coin, so the arm stays exactly where you put it instead of drifting down over a month.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 340mm, width 180mm, projection from the wall 180mm to 520mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout with a hand rolled linen shade\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 180mm to 520mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.6 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767014003020,"sku":"SCH-SWG-001-AB","price":739.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767014035788,"sku":"SCH-SWG-001-PB","price":739.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767014068556,"sku":"SCH-SWG-001-PN","price":789.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767014101324,"sku":"SCH-SWG-001-BZ","price":809.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Hollis_Solid_Brass_Swing_Arm_with_a_Linen_Shade_Wall_Light.jpg?v=1789048495"},{"product_id":"marlow-and-reade-hollis-solid-brass-swing-arm-with-a-linen-shade-wall-light-pair","title":"Marlow and Reade Hollis Solid Brass Swing Arm with a Linen Shade Wall Light Pair","description":"\u003cp\u003eA single jointed swing arm with a hand rolled linen shade. The joint is a brass friction knuckle you tighten with a coin, so the arm stays exactly where you put it instead of drifting down over a month.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold as a pair for either side of a bed.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 340mm, width 180mm, projection from the wall 180mm to 520mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout with a hand rolled linen shade\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 180mm to 520mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 7.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767014166860,"sku":"SCH-SWG-002-AB","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767014199628,"sku":"SCH-SWG-002-PB","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767014232396,"sku":"SCH-SWG-002-PN","price":1524.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767014265164,"sku":"SCH-SWG-002-BZ","price":1549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Hollis_Solid_Brass_Swing_Arm_with_a_Linen_Shade_Wall_Light_Pair.jpg?v=1789048363"},{"product_id":"marlow-and-reade-hollis-solid-brass-swing-arm-with-a-linen-shade-wall-light-plug-in","title":"Marlow and Reade Hollis Solid Brass Swing Arm with a Linen Shade Wall Light Plug In","description":"\u003cp\u003eA single jointed swing arm with a hand rolled linen shade. The joint is a brass friction knuckle you tighten with a coin, so the arm stays exactly where you put it instead of drifting down over a month.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Supplied as a plug in fitting with a two metre braided flex, a moulded UK plug and an inline switch.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 340mm, width 180mm, projection from the wall 180mm to 520mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout with a hand rolled linen shade\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: plug in, 2 metre braided flex with a moulded UK plug fitted\u003c\/li\u003e\n\u003cli\u003eSwitching: inline rocker switch on the flex, 400mm from the fitting\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 180mm to 520mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.8 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a plug in fitting, so no electrician is needed. Two keyhole slots on the backplate take a pair of screws, and the flex drops from the lower edge of the backplate. If you would rather run the cable down inside the wall, an electrician can convert it to a hardwired fitting and the flex simply comes off. At roughly 3.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767014297932,"sku":"SCH-SWG-003-AB","price":789.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767014330700,"sku":"SCH-SWG-003-PB","price":789.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767014363468,"sku":"SCH-SWG-003-PN","price":839.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767014396236,"sku":"SCH-SWG-003-BZ","price":859.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Hollis_Solid_Brass_Swing_Arm_with_a_Linen_Shade_Wall_Light_Plug_In.jpg?v=1789048365"},{"product_id":"marlow-and-reade-ingleby-solid-brass-double-jointed-library-arm-wall-light-pair","title":"Marlow and Reade Ingleby Solid Brass Double Jointed Library Arm Wall Light Pair","description":"\u003cp\u003eTwo joints and a longer reach, the arm a library would have fitted over a reading chair. It folds flat to 150mm when you are not using it and pulls out to almost three quarters of a metre when you are.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold as a pair for either side of a bed.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 300mm, width 160mm, projection from the wall 150mm to 740mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 150mm to 740mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 8.8 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 8.8 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767014560076,"sku":"SCH-SWG-005-AB","price":1724.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767014592844,"sku":"SCH-SWG-005-PB","price":1724.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767014625612,"sku":"SCH-SWG-005-PN","price":1824.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767014658380,"sku":"SCH-SWG-005-BZ","price":1874.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Ingleby_Solid_Brass_Double_Jointed_Library_Arm_Wall_Light_Pair.jpg?v=1789048688"},{"product_id":"marlow-and-reade-ingleby-solid-brass-double-jointed-library-arm-wall-light-plug-in","title":"Marlow and Reade Ingleby Solid Brass Double Jointed Library Arm Wall Light Plug In","description":"\u003cp\u003eTwo joints and a longer reach, the arm a library would have fitted over a reading chair. It folds flat to 150mm when you are not using it and pulls out to almost three quarters of a metre when you are.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Supplied as a plug in fitting with a two metre braided flex, a moulded UK plug and an inline switch.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 300mm, width 160mm, projection from the wall 150mm to 740mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: plug in, 2 metre braided flex with a moulded UK plug fitted\u003c\/li\u003e\n\u003cli\u003eSwitching: inline rocker switch on the flex, 400mm from the fitting\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 150mm to 740mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.6 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a plug in fitting, so no electrician is needed. Two keyhole slots on the backplate take a pair of screws, and the flex drops from the lower edge of the backplate. If you would rather run the cable down inside the wall, an electrician can convert it to a hardwired fitting and the flex simply comes off. At roughly 4.6 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767014691148,"sku":"SCH-SWG-006-AB","price":949.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767014723916,"sku":"SCH-SWG-006-PB","price":949.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767014756684,"sku":"SCH-SWG-006-PN","price":999.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767014789452,"sku":"SCH-SWG-006-BZ","price":1024.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Ingleby_Solid_Brass_Double_Jointed_Library_Arm_Wall_Light_Plug_In.jpg?v=1789048650"},{"product_id":"marlow-and-reade-jesmond-solid-brass-reading-arm-with-a-metal-cone-shade-wall-light","title":"Marlow and Reade Jesmond Solid Brass Reading Arm with a Metal Cone Shade Wall Light","description":"\u003cp\u003eA spun brass cone on an adjustable arm, the shade deep enough to keep the lamp out of the eye of anyone lying down. This is the one people buy for a bedside when they read and their partner does not.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 260mm, width 150mm, projection from the wall 170mm to 480mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 170mm to 480mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.1 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 3.1 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767014854988,"sku":"SCH-SWG-007-AB","price":679.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767014887756,"sku":"SCH-SWG-007-PB","price":679.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767014920524,"sku":"SCH-SWG-007-PN","price":719.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767014953292,"sku":"SCH-SWG-007-BZ","price":739.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Jesmond_Solid_Brass_Reading_Arm_with_a_Metal_Cone_Shade_Wall_Light.jpg?v=1789048609"},{"product_id":"marlow-and-reade-jesmond-solid-brass-reading-arm-with-a-metal-cone-shade-wall-light-pair","title":"Marlow and Reade Jesmond Solid Brass Reading Arm with a Metal Cone Shade Wall Light Pair","description":"\u003cp\u003eA spun brass cone on an adjustable arm, the shade deep enough to keep the lamp out of the eye of anyone lying down. This is the one people buy for a bedside when they read and their partner does not.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold as a pair for either side of a bed.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 260mm, width 150mm, projection from the wall 170mm to 480mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 170mm to 480mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.2 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767014986060,"sku":"SCH-SWG-008-AB","price":1299.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767015018828,"sku":"SCH-SWG-008-PB","price":1299.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767015051596,"sku":"SCH-SWG-008-PN","price":1374.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767015084364,"sku":"SCH-SWG-008-BZ","price":1424.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Jesmond_Solid_Brass_Reading_Arm_with_a_Metal_Cone_Shade_Wall_Light_Pair.jpg?v=1789048649"},{"product_id":"marlow-and-reade-jesmond-solid-brass-reading-arm-with-a-metal-cone-shade-wall-light-plug-in","title":"Marlow and Reade Jesmond Solid Brass Reading Arm with a Metal Cone Shade Wall Light Plug In","description":"\u003cp\u003eA spun brass cone on an adjustable arm, the shade deep enough to keep the lamp out of the eye of anyone lying down. This is the one people buy for a bedside when they read and their partner does not.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Supplied as a plug in fitting with a two metre braided flex, a moulded UK plug and an inline switch.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 260mm, width 150mm, projection from the wall 170mm to 480mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E14 candle, maximum 40W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: plug in, 2 metre braided flex with a moulded UK plug fitted\u003c\/li\u003e\n\u003cli\u003eSwitching: inline rocker switch on the flex, 400mm from the fitting\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 170mm to 480mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.3 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a plug in fitting, so no electrician is needed. Two keyhole slots on the backplate take a pair of screws, and the flex drops from the lower edge of the backplate. If you would rather run the cable down inside the wall, an electrician can convert it to a hardwired fitting and the flex simply comes off. At roughly 3.3 kilograms it is light enough for a good quality plasterboard anchor if there is no timber behind.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767015149900,"sku":"SCH-SWG-009-AB","price":719.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767015182668,"sku":"SCH-SWG-009-PB","price":719.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767015215436,"sku":"SCH-SWG-009-PN","price":759.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767015248204,"sku":"SCH-SWG-009-BZ","price":779.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Jesmond_Solid_Brass_Reading_Arm_with_a_Metal_Cone_Shade_Wall_Light_Plug_In.jpg?v=1789048606"},{"product_id":"marlow-and-reade-kelmarsh-solid-brass-articulated-arm-with-a-counterweight-wall-light","title":"Marlow and Reade Kelmarsh Solid Brass Articulated Arm with a Counterweight Wall Light","description":"\u003cp\u003eAn articulated arm balanced by a solid brass counterweight, the drawing office pattern. The balance means you move it with one finger and it stays put, which no friction joint quite manages.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 420mm, width 200mm, projection from the wall 220mm to 900mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 220mm to 900mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.8 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 6.8 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767015280972,"sku":"SCH-SWG-010-AB","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767015313740,"sku":"SCH-SWG-010-PB","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767015346508,"sku":"SCH-SWG-010-PN","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767015379276,"sku":"SCH-SWG-010-BZ","price":1299.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Kelmarsh_Solid_Brass_Articulated_Arm_with_a_Counterweight_Wall_Light.jpg?v=1789048706"},{"product_id":"marlow-and-reade-kelmarsh-solid-brass-articulated-arm-with-a-counterweight-wall-light-pair","title":"Marlow and Reade Kelmarsh Solid Brass Articulated Arm with a Counterweight Wall Light Pair","description":"\u003cp\u003eAn articulated arm balanced by a solid brass counterweight, the drawing office pattern. The balance means you move it with one finger and it stays put, which no friction joint quite manages.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold as a pair for either side of a bed.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 420mm, width 200mm, projection from the wall 220mm to 900mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 220mm to 900mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.6 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 13.6 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767016788300,"sku":"SCH-SWG-011-AB","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767016821068,"sku":"SCH-SWG-011-PB","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767016853836,"sku":"SCH-SWG-011-PN","price":2424.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767016886604,"sku":"SCH-SWG-011-BZ","price":2499.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Kelmarsh_Solid_Brass_Articulated_Arm_with_a_Counterweight_Wall_Light_Pair.jpg?v=1789048705"},{"product_id":"marlow-and-reade-kelmarsh-solid-brass-articulated-arm-with-a-counterweight-wall-light-plug-in","title":"Marlow and Reade Kelmarsh Solid Brass Articulated Arm with a Counterweight Wall Light Plug In","description":"\u003cp\u003eAn articulated arm balanced by a solid brass counterweight, the drawing office pattern. The balance means you move it with one finger and it stays put, which no friction joint quite manages.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Supplied as a plug in fitting with a two metre braided flex, a moulded UK plug and an inline switch.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 420mm, width 200mm, projection from the wall 220mm to 900mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: plug in, 2 metre braided flex with a moulded UK plug fitted\u003c\/li\u003e\n\u003cli\u003eSwitching: inline rocker switch on the flex, 400mm from the fitting\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 220mm to 900mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.1 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a plug in fitting, so no electrician is needed. Two keyhole slots on the backplate take a pair of screws, and the flex drops from the lower edge of the backplate. If you would rather run the cable down inside the wall, an electrician can convert it to a hardwired fitting and the flex simply comes off. At roughly 7.1 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767018000716,"sku":"SCH-SWG-012-AB","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767018033484,"sku":"SCH-SWG-012-PB","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767018066252,"sku":"SCH-SWG-012-PN","price":1349.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767018099020,"sku":"SCH-SWG-012-BZ","price":1374.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Kelmarsh_Solid_Brass_Articulated_Arm_with_a_Counterweight_Wall_Light_Plug_In.jpg?v=1789048601"},{"product_id":"marlow-and-reade-lambourne-solid-brass-gooseneck-with-milk-glass-wall-light","title":"Marlow and Reade Lambourne Solid Brass Gooseneck with Milk Glass Wall Light","description":"\u003cp\u003eA heavy gooseneck in solid brass with a milk glass shade screwed into a brass gallery. The gooseneck holds any position you bend it into and will keep doing so for decades because the tube is thick walled.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold singly.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 380mm, width 180mm, projection from the wall 300mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout with a milk glass shade\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 300mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.2 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. At roughly 4.2 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767018492236,"sku":"SCH-SWG-013-AB","price":819.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767018525004,"sku":"SCH-SWG-013-PB","price":819.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767018557772,"sku":"SCH-SWG-013-PN","price":869.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767018590540,"sku":"SCH-SWG-013-BZ","price":899.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Lambourne_Solid_Brass_Gooseneck_with_Milk_Glass_Wall_Light.jpg?v=1789048650"},{"product_id":"marlow-and-reade-lambourne-solid-brass-gooseneck-with-milk-glass-wall-light-pair","title":"Marlow and Reade Lambourne Solid Brass Gooseneck with Milk Glass Wall Light Pair","description":"\u003cp\u003eA heavy gooseneck in solid brass with a milk glass shade screwed into a brass gallery. The gooseneck holds any position you bend it into and will keep doing so for decades because the tube is thick walled.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Sold as a pair for either side of a bed.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight, per fitting: 380mm, width 180mm, projection from the wall 300mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout with a milk glass shade\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp, per fitting: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: hardwired, 220 to 240V, 50Hz, terminal block behind the backplate\u003c\/li\u003e\n\u003cli\u003eSwitching: rocker switch on the backplate\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 300mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 8.4 kilograms for the pair\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold as a pair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a hardwired fitting and should be installed by a qualified electrician working to BS 7671. It arrives with a standard round backplate and fixing screws. Wall plugs are not supplied because the right fixing depends on whether you are going into brick, block, plasterboard or lath and plaster. It is a heavy fitting at roughly 8.4 kilograms, so fix into masonry or into a timber noggin behind plasterboard rather than into the board alone.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767019082060,"sku":"SCH-SWG-014-AB","price":1574.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767019114828,"sku":"SCH-SWG-014-PB","price":1574.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767019147596,"sku":"SCH-SWG-014-PN","price":1674.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767019180364,"sku":"SCH-SWG-014-BZ","price":1724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Lambourne_Solid_Brass_Gooseneck_with_Milk_Glass_Wall_Light_Pair.jpg?v=1789048706"},{"product_id":"marlow-and-reade-lambourne-solid-brass-gooseneck-with-milk-glass-wall-light-plug-in","title":"Marlow and Reade Lambourne Solid Brass Gooseneck with Milk Glass Wall Light Plug In","description":"\u003cp\u003eA heavy gooseneck in solid brass with a milk glass shade screwed into a brass gallery. The gooseneck holds any position you bend it into and will keep doing so for decades because the tube is thick walled.\u003c\/p\u003e\u003cp\u003eTurned and machined from solid brass bar in Birmingham, not spun from sheet and not plated steel. The arms run on machined brass knuckles with PTFE washers, so the movement is smooth from the first day and stays that way. Finishes are applied to the metal itself, so a scratch shows brass underneath rather than a different colour. Supplied as a plug in fitting with a two metre braided flex, a moulded UK plug and an inline switch.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHeight 380mm, width 180mm, projection from the wall 300mm\u003c\/li\u003e\n\u003cli\u003eMaterials: solid brass throughout with a milk glass shade\u003c\/li\u003e\n\u003cli\u003eFinish: living finish, will mellow with handling unless lacquered\u003c\/li\u003e\n\u003cli\u003eLamp: 1 x E27, maximum 60W, dimmable LED suitable\u003c\/li\u003e\n\u003cli\u003eSupply: plug in, 2 metre braided flex with a moulded UK plug fitted\u003c\/li\u003e\n\u003cli\u003eSwitching: inline rocker switch on the flex, 400mm from the fitting\u003c\/li\u003e\n\u003cli\u003eRating: IP20, for dry indoor rooms\u003c\/li\u003e\n\u003cli\u003eBackplate: round solid brass, 105mm diameter, 8mm thick\u003c\/li\u003e\n\u003cli\u003eReach: 300mm from the wall\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 4.4 kilograms\u003c\/li\u003e\n\u003cli\u003eLead time: 2 to 3 weeks\u003c\/li\u003e\n\u003cli\u003eSold singly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eThis is a plug in fitting, so no electrician is needed. Two keyhole slots on the backplate take a pair of screws, and the flex drops from the lower edge of the backplate. If you would rather run the cable down inside the wall, an electrician can convert it to a hardwired fitting and the flex simply comes off. At roughly 4.4 kilograms it needs a proper fixing. Use the supplied screws into masonry, or a heavy duty plasterboard anchor rated well above the weight of the light.\u003c\/p\u003e","brand":"Marlow and Reade","offers":[{"title":"Antique brass","offer_id":58767019639116,"sku":"SCH-SWG-015-AB","price":869.0,"currency_code":"GBP","in_stock":true},{"title":"Polished brass","offer_id":58767019671884,"sku":"SCH-SWG-015-PB","price":869.0,"currency_code":"GBP","in_stock":true},{"title":"Polished nickel","offer_id":58767019704652,"sku":"SCH-SWG-015-PN","price":929.0,"currency_code":"GBP","in_stock":true},{"title":"Bronze","offer_id":58767019737420,"sku":"SCH-SWG-015-BZ","price":949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1089\/3128\/5324\/files\/Marlow_and_Reade_Lambourne_Solid_Brass_Gooseneck_with_Milk_Glass_Wall_Light_Plug_In.jpg?v=1789048790"}],"url":"https:\/\/thesconcehouse.com\/collections\/bedside-wall-lights.oembed?page=2","provider":"The Sconce House","version":"1.0","type":"link"}